Monopropellant propulsion stores and feeds one propellant formulation to the thruster. A catalyst, heat or another initiation mechanism triggers decomposition or reaction, producing hot gas that expands through a nozzle. Monopropellant describes the single stored feed: an ionic-liquid blend can contain both fuel and oxidising species within that formulation.12

Thruster and feed architecture

A pressure-fed system commonly comprises a propellant tank, pressurant or blowdown volume, isolation and flow-control valves, filter, lines, injector, catalyst bed or chamber, heaters, temperature sensing and a nozzle.13 It avoids the second tank and matched fuel/oxidiser plumbing of a bipropellant system, but integrated performance still depends on inlet pressure, valve response, thermal state and propellant acquisition.

Hydrazine spacecraft thrusters normally pass the liquid over an iridium-on-alumina catalyst such as Shell 405. Exothermic decomposition produces the hot gases; it is therefore more precise to describe catalytic decomposition than to say simply that hydrazine burns.1 The catalyst bed often needs thermal conditioning. Contamination, mechanical degradation, cold starts, pulse history and cumulative throughput can change ignition delay and delivered impulse.

Performance with conditions

Nammo’s UK-made MHT-1N data sheet specifies 1.295 N nominal thrust at 24 bar absolute and more than 228 seconds specific impulse at its 1.38 N maximum thrust.4 The same record gives a demonstrated 15 ms minimum on-time, but those figures belong to the stated thruster, pressure, valve and hydrazine configuration.

Its ESA qualification figures include 19.19 kg hydrazine throughput, 36,849 N s total impulse, 87,818 pulses and two cold starts with the catalyst bed between 5 °C and 10 °C. Nammo also records a January 2018 first flight on SSTL’s Telesat LEO-1.4 These are useful bounded flight and qualification data, rather than general limits for 1 N-class monopropellant systems.

NASA’s Green Propellant Infusion Mission tested the ASCENT formulation, formerly AF-M315E, with its compatible tanks, valves and five thrusters in orbit. Planned attitude-control and orbit-lowering manoeuvres demonstrated the projected mission performance.2 NASA described a 50% improvement in gas mileage over the mission’s hydrazine comparison; that result should remain attached to GPIM and not be recast as a universal specific-impulse or spacecraft-mass benefit.

Propellants, handling and storability

Hydrazine has extensive flight heritage, but it is corrosive, highly toxic and potentially carcinogenic. Loading operations use specialist controls and protective ensembles: ESA’s June 2023 Euclid fuelling record documents 140 kg in one central tank and technicians wearing self-contained atmospheric protective suits.5 UK Health Security Agency guidance provides current health-effect and incident-response context, while project-specific standards govern spacecraft processing.6

Lower-toxicity formulations such as ASCENT can reduce vapour and personal-protective-equipment burdens relative to hydrazine, but they remain energetic chemicals and require compatible tanks, seals, valves, filters and heaters.12 Green is therefore a relative handling label, not evidence of harmlessness or a complete lifecycle assessment.

Storability has thermal limits. NASA reports that hydrazine freezes near 1.6 °C; freeze–thaw can rupture confined plumbing, compromise seals and valves, create slush blockage and cause a hard start or misfire.7 Temperature sensors alone may not capture the coldest point, so analysis, heaters, insulation and controlled ground handling need uncertainty margin.

Qualification and failure

Qualification must represent pressure, propellant and catalyst temperature, pulses and long burns, minimum impulse bit, restarts, throughput, valve cycles and environmental loads.3 Before GPIM, NASA tested non-flight 1 N and 22 N valves from 125 to 410 psig at multiple temperatures because ASCENT’s fluid properties vary with temperature.8 Separate vacuum plume work used spectroscopy and imaging, followed by pulse and steady tests, before the successful 13-month flight demonstration.9

Credible failures include leakage, a valve stuck open or closed, filter or injector blockage, catalyst poisoning or breakup, insufficient preheat, thermal hard start and falling performance with contamination. A NASA technical bulletin reports that contaminants not fully controlled by the high-purity hydrazine procurement specification have caused flow decay in small thrusters.10 Redundant valves and filtration reduce selected risks but do not remove the need for cleanliness, compatible materials and health monitoring.

UK capability

The MHT-1N establishes a bounded UK example: it was developed by Nammo UK at Westcott, qualified for ESA’s NeoSat platforms and flown on Telesat LEO-1 according to the manufacturer’s data sheet.4 Those claims concern the named thruster. A new integrated propulsion subsystem still needs qualification for its own tankage, feed, control, thermal design, duty cycle and mission environment.

References

Footnotes

  1. NASA Small Spacecraft Systems Virtual Institute, In-Space Propulsion. ↩ ↩2 ↩3 ↩4

  2. NASA, Green Propellant Infusion Mission nears completion. ↩ ↩2 ↩3

  3. European Cooperation for Space Standardization, ECSS-E-ST-35-01C: Liquid and electric propulsion for spacecraft. ↩ ↩2

  4. Nammo, MHT-1N Monopropellant Hydrazine Thruster. ↩ ↩2 ↩3

  5. European Space Agency, Euclid fuelled for launch. ↩

  6. UK Health Security Agency, Hydrazine: general information and incident management. ↩

  7. NASA Engineering and Safety Center, Risk of Hydrazine Use Following Freeze–Thaw Exposure. ↩

  8. NASA Technical Reports Server, GPIM Thruster Valve Testing. ↩

  9. NASA Glenn Research Center, Rocket Laboratory — Final Years. ↩

  10. NASA Engineering and Safety Center, Contaminant Reduction in High Purity Hydrazine. ↩